How to apply our Iron on Cotton Patches

Vintage-Patch patches are easy to apply, and each pack includes a test sample for a trial run.  *Additional sewing required for some items – please see notes at the bottom.

  1. Ensure the garment you wish to apply patches to can be ironed at a hot iron temperature.
  2. Decide on positioning. For elbow or knee patches, it’s a good idea to put the garment on, bend your arm or leg and mark your elbow or knee position on the garment with a pin.

    3. Once you’ve placed the patch in a position you are happy with, match up with the other sleeve or leg  carefully so patches are equally positioned. 4. Mark position with pins (or chalk, sparingly!).
  3. Remove any water from of the reservoir of your iron and switch off the ‘steam/spray’ action as this can compromised the adhesive.  Make sure your iron is cleaned of any residue on the plate.
  4. Remove the backing paper from the sample snippet in the pack. Using the HOTTEST iron setting your garment will allow, carry out a trial run with this onto a scrap of waste fabric. The Linen/Max setting is appropriate for denim patches, a slightly lower Cotton /blends temp should be effective for our thinner cotton patches.  Use a lift and press motion for up to 60 seconds on each side of the sample. The aim is to fully melt the adhesive so the glue meshes with the fabric fibres of your garment – without scorching.
  5. Allow the snippet to cool for 20 minutes and check the bond, which should be firm once it has cooled and ‘set’ (the patch may still lift up while the glue is warm). If a good bond was achieved with the sample, you have established the correct temperature for your iron.
  6. Carefully lift up a corner of the patch’s backing paper so you can see the shiny glue surface (if the glue is not visible on the fabric, you may have lifted it with the backing (in this case, re-iron the lifted area of backing on to the patch at medium heat, allow to cool and try again).  Remove backing before application.
    Place patch into position glue side down, and press over all areas of it from back and front for 20 to 60 seconds as described above to ensure the glue melts and the entire piece is well bonded.  Lay the fused parts flat and allow to cool for about 20 minutes.
    *Although in most cases we recommend you iron straight on top of the fabric, for some garments use of a press cloth may be appropriate.  Please use the thinnest cloth possible (eg cotton muslin) so that you still reach the required temperature to melt the glue and achieve a good bond. You may need extra pressing time also.  This is especially true of garments and patches made of thicker fabrics such as denim or wool.
  7. Our adhesive may not to need extra sewing on some tight weave fabrics such as cotton, polyester cotton and denim. However, adherence depends on sufficiently hot iron temperature which not all fabrics will tolerate and the amout of wear, tear and washing a garment will receive – tumble drying for example is very likely to loosen the bond. Therefore we always recommend overstitching for a more attractive and long lasting ‘finish’ to the garment.  The can be carried out very easily and quickly as seen below.Below: Patch secured with Running Stitch

    Below: Patch secured with Blanket Stitch.
  8. The adhesive is not suitable for nylon or very stretchy fabrics . Loose weave, textured, napped or moderately stretchy fabrics  will require extra stitching round the edges using a machine zig zag setting,  or hand stitching –  a simple running stitch in matching or contrast thread  is quick and easy.  Alternatively,  hand sew using a blanket stitch for a traditional finish.  There is some useful advice on stiches here: http://www.instructables.com/id/Embroidery-101/step4/The-running-stitch/  and  http://www.instructables.com/id/Embroidery-101/step8/Blanket-stitch/
  9. As garments and irons vary, we cannot guarantee a permanent no sew bond in all cases. If you find that your patches lift after application, or become loose after washing and wear, simply secure the edges with a line of running stitch in matching or contrast thread for a long lasting and attractive finish.
  10. Vintage-Patch fabrics are prewashed for colourfastness, but we do recommend that if strongly coloured patches are applied to light coloured garments, you add a ‘colour catcher’ cloth to the first couple of washes.  Our fabrics are suitable for machine or hand washing at 40 degrees. *Tumble drying is not recommended for unstitched patches.


    Stitching is required for:

    Items dried using a tumble dryer
    Heavy duty items that are frequently laundered
    Loose weave, textured, napped or moderately stretchy fabrics.
    Our patches are not suitable for
    Nylon, fabrics with waterproof or special finishes or very stretchy fabrics

    BUY PATCHES FROM OUR RANGE

Leave a Reply

Your email address will not be published. Required fields are marked *